Deck Calculator

Enter the deck size, the board size and the joist spacing. You get a full material list: deck boards, joists, beams, posts, footings, concrete and screws or hidden clips. It is a material estimate, not a structural design.

Joists run this way.

On: a ledger and one beam. Off: freestanding on two beams.

Check the span rating of 5/4 or composite boards before using 24 in.

1/8 in is 0.125.

45 degrees to the joists. Turning this on raises the waste allowance.

The farthest apart you want posts.

Deck board fasteners

Used to read joist and beam sizes from the DCA 6 span tables.

Leave at 0 to skip cost.

Printed on the saved result.

Deck material estimate

Your deck materials

Deck boards, 16 ft

29 boards

For a 16 x 12 ft deck, 192 sq ft, with 10% waste. A material estimate, not a structural design.

Joists

13 x 2x10

Posts and footings

3

Material list
MaterialQuantity
Deck boards, 16 ft26 rows of 6 in deck boards with a 0.125 in gap, 10% waste29 boards
Joists, 2x10 x 12 ft16 in on center across 16 ft, both ends included. 2x10 is the smallest in DCA 6 Table 2 for a 12 ft span13 joists
Rim joistAcross the outer ends of the joists16 linear ft
Ledger boardAgainst the house, 2x8 or larger under DCA 616 linear ft
Joist hangersOne per joist at the ledger13 hangers
Beams, 2-ply 2x1216 ft long, 32 linear ft of 2x12 in all. Smallest in DCA 6 Table 3A for posts 8 ft apart1 beam
Posts, 6x63 per beam, 8 ft apart. Length depends on deck height3 posts
Footings24 in round or 21 in square, 10 in thick (DCA 6 Table 4, 1,500 psf soil)3 footings
Concrete for footing pads7.9 cu ft for the pads alone. Piers down to frost depth add more14 80 lb bags
Deck screws338 board-over-joist crossings, two screws at each, plus 10%744
How we calculated this

This is a material estimate, not a structural design.The joist, beam and footing sizes are read from the American Wood Council's DCA 6 guide for a single-level deck with a 40 psf live load, 10 psf dead load, No. 2 lumber and 1,500 psf soil. Your building department decides what is allowed, and snow load, height, soil, hot tubs and stairs all change the answer.

Deck boards. Boards run along the house. Rows are the deck depth divided by the board width plus the gap. Each row takes the deck width in boards of the length you picked, and a board longer than the deck still counts as one board. The waste allowance starts at 10% for boards square to the joists and 15% for boards at 45 degrees.

Joists. One at each end and one at every spacing across the width, each as long as the deck is deep and bought in the next even length. The size shown is the smallest in DCA 6 Table 2 that spans the full depth in Southern Pine. The table stops at 18 ft.

Beams, posts and footings. An attached deck gets a ledger at the house and one beam at the outer end. A freestanding deck gets two beams. Posts are spaced evenly along each beam, no farther apart than you entered, with one at each end. The beam is the smallest built-up size in Table 3A for that post spacing, and the footing size comes from Table 4. DCA 6 uses 6x6 posts as its minimum.

Concrete. The volume of the Table 4 footing pads only, at 0.60 cu ft per 80 lb bag. DCA 6 puts footings at least 12 inches below undisturbed ground or below the frost line, whichever is deeper, so piers in a cold climate need more concrete than this line shows.

Fasteners. DCA 6 fastens each board with two screws or nails at every joist, so screws are two per crossing. Hidden clips are one per crossing. As a cross-check, Trex packs 90 clips to cover 50 sq ft at 16 in on center. Both counts include your waste allowance.

Not counted. Stairs, railings, guard posts, blocking, flashing, ledger bolts, post bases and beam hardware.

Sources for the figures used, all opened on November 20, 2026:

Save your result

Example: a 16 x 12 ft deck attached to the house

A 16 x 12 ft attached deck is 192 sq ft. With 6 in boards 16 ft long, joists 16 in on center and 10% waste, it takes 29 deck boards, 13 joists (2x10 in Southern Pine under the American Wood Council DCA 6 span table), one beam on 3 posts and footings, and 744 deck screws. This is a material estimate, not a structural design.

Example deck materials

Deck boards, 16 ft

29 boards

For a 16 x 12 ft deck, 192 sq ft, with 10% waste. A material estimate, not a structural design.

Joists

13 x 2x10

Posts and footings

3

Material list
MaterialQuantity
Deck boards, 16 ft26 rows of 6 in deck boards with a 0.125 in gap, 10% waste29 boards
Joists, 2x10 x 12 ft16 in on center across 16 ft, both ends included. 2x10 is the smallest in DCA 6 Table 2 for a 12 ft span13 joists
Rim joistAcross the outer ends of the joists16 linear ft
Ledger boardAgainst the house, 2x8 or larger under DCA 616 linear ft
Joist hangersOne per joist at the ledger13 hangers
Beams, 2-ply 2x1216 ft long, 32 linear ft of 2x12 in all. Smallest in DCA 6 Table 3A for posts 8 ft apart1 beam
Posts, 6x63 per beam, 8 ft apart. Length depends on deck height3 posts
Footings24 in round or 21 in square, 10 in thick (DCA 6 Table 4, 1,500 psf soil)3 footings
Concrete for footing pads7.9 cu ft for the pads alone. Piers down to frost depth add more14 80 lb bags
Deck screws338 board-over-joist crossings, two screws at each, plus 10%744
How we calculated this

This is a material estimate, not a structural design.The joist, beam and footing sizes are read from the American Wood Council's DCA 6 guide for a single-level deck with a 40 psf live load, 10 psf dead load, No. 2 lumber and 1,500 psf soil. Your building department decides what is allowed, and snow load, height, soil, hot tubs and stairs all change the answer.

Deck boards. Boards run along the house. Rows are the deck depth divided by the board width plus the gap. Each row takes the deck width in boards of the length you picked, and a board longer than the deck still counts as one board. The waste allowance starts at 10% for boards square to the joists and 15% for boards at 45 degrees.

Joists. One at each end and one at every spacing across the width, each as long as the deck is deep and bought in the next even length. The size shown is the smallest in DCA 6 Table 2 that spans the full depth in Southern Pine. The table stops at 18 ft.

Beams, posts and footings. An attached deck gets a ledger at the house and one beam at the outer end. A freestanding deck gets two beams. Posts are spaced evenly along each beam, no farther apart than you entered, with one at each end. The beam is the smallest built-up size in Table 3A for that post spacing, and the footing size comes from Table 4. DCA 6 uses 6x6 posts as its minimum.

Concrete. The volume of the Table 4 footing pads only, at 0.60 cu ft per 80 lb bag. DCA 6 puts footings at least 12 inches below undisturbed ground or below the frost line, whichever is deeper, so piers in a cold climate need more concrete than this line shows.

Fasteners. DCA 6 fastens each board with two screws or nails at every joist, so screws are two per crossing. Hidden clips are one per crossing. As a cross-check, Trex packs 90 clips to cover 50 sq ft at 16 in on center. Both counts include your waste allowance.

Not counted. Stairs, railings, guard posts, blocking, flashing, ledger bolts, post bases and beam hardware.

Sources for the figures used, all opened on November 20, 2026:

How to calculate deck materials

A deck material list is built in layers: deck boards on joists, joists on a ledger and a beam, the beam on posts, posts on footings. Each layer is a count you can work out from the deck's width, its depth and one spacing. This calculator is a material estimate, not a structural design, so treat the sizes it names as a starting point for the plan your building department reviews.

The formulas:

  1. Rows of deck boards = deck depth in inches divided by (board width + gap), rounded up.
  2. Deck boards = rows x (deck width divided by board length, at least 1) x (1 + waste percent), rounded up.
  3. Joists = deck width in inches divided by joist spacing, rounded up, plus 1.
  4. Posts per beam = deck width divided by post spacing, rounded up, plus 1.
  5. Screws = rows x joists x 2, plus waste. Hidden clips are rows x joists, plus waste.

A worked example

Take a deck 16 ft wide along the house and 12 ft deep, attached with a ledger. The depth is 144 in, and a 5.5 in board with a 1/8 in gap takes 5.625 in, so there are 26 rows. Each row is one 16 ft board, and 26 boards plus 10% waste is 29 boards.

The width is 192 in, so joists at 16 in on center make 12 spaces and 13 joists, each 12 ft long. The joists span 12 ft, and in Southern Pine the DCA 6 table needs a 2x10 for that at 16 in on center, because a 2x8 stops at 11 ft 10 in.

Posts no more than 8 ft apart along the 16 ft beam means 3 posts and 3 footings. For posts 8 ft apart under 12 ft joists, the smallest Southern Pine beam in the table is two 2x12s, and the footing is 24 in round and 10 in thick. The boards cross the joists 338 times, so the deck takes 676 screws, or 744 with 10% extra.

Where the span numbers come from

The joist, beam and footing sizes are read from DCA 6, the Prescriptive Residential Wood Deck Construction Guide published by the American Wood Council and based on the 2015 International Residential Code. Its tables assume a 40 psf live load, a 10 psf dead load, No. 2 grade lumber in wet service and soil that can carry 1,500 psf.

The guide has limits, and the calculator tells you when you are outside them:

  • It covers single-level decks, and joists and beams up to 18 ft.
  • The deck may be no deeper than it is wide along the house.
  • Posts are 6x6 at minimum.
  • The ledger is 2x8 or larger.
  • Hot tubs, and snow loads over 40 psf, are outside the guide.

What moves the count

  • Board length. Boards that match the deck width mean no butt joints and less waste. Shorter boards add joints, and every joint must land on a joist.
  • Joist spacing. Going from 16 in to 12 in adds a third more joists, hangers and screws. Some decking makers call for tighter spacing, especially under diagonal boards, so read the instructions for the board you are using.
  • Diagonal boards. The area is the same but every board is cut at both ends, so the waste allowance starts at 15% instead of 10%.
  • Post spacing. Fewer posts means fewer holes to dig and a bigger beam. More posts means the opposite.
  • Frost depth. The concrete line counts the footing pads only. Piers that reach below a deep frost line take more.

Turning the list into a price

For a contractor, this list is the material half of the quote. Stairs, railings, hardware, permits and labor are the other half. Put both halves in one document with the estimate template, and mark up materials before you send it.

Common Questions

How many deck boards do I need?

Divide the deck depth in inches by the board width plus the gap to get the number of rows, then multiply by the boards each row takes and add waste. A 12 ft deep deck is 144 in. With 5.5 in boards and a 1/8 in gap that is 26 rows. On a 16 ft wide deck each row is one 16 ft board, so 26 boards, and 29 with 10% waste.

How many joists do I need for a deck?

Divide the deck width in inches by the joist spacing, round up and add one for the last joist. A 16 ft wide deck is 192 in. At 16 in on center that is 12 spaces and 13 joists. Rim joists across the ends and the ledger against the house are counted separately.

How far can a deck joist span?

It depends on the size, the species and the spacing. In the American Wood Council's DCA 6 guide, a Southern Pine 2x8 at 16 in on center spans up to 11 ft 10 in and a 2x10 spans up to 14 ft. The table assumes a 40 psf live load and No. 2 grade lumber, and it stops at 18 ft. Your local code can be stricter, especially where snow load is high.

How far apart should deck posts be?

As far as the beam can span, and no farther. In DCA 6 a Southern Pine beam made of two 2x12s spans up to 8 ft 4 in between posts when it carries joists that span 12 ft, and a beam of two 2x10s spans up to 7 ft 1 in. Heavier loads and longer joists shorten that. Enter the spacing you want and the calculator names the smallest beam in the table that covers it.

What size footings does a deck need?

It depends on how much deck each post carries and on the soil. DCA 6 Table 4 gives a round footing 24 in across and 10 in thick for posts 8 ft apart carrying joists up to 14 ft, on soil rated at 1,500 psf. Footings must also reach at least 12 inches below undisturbed ground or below the frost line, whichever is deeper. Your building department sets the frost depth.

How many screws do I need for a deck?

Two for every place a board crosses a joist, which is what DCA 6 calls for. Multiply the rows of boards by the number of joists, then by two. A 16 x 12 ft deck with 26 rows and 13 joists has 338 crossings and takes 676 screws, or 744 with 10% extra. Hidden clips are one per crossing.

Can I use this calculator to get a deck permit?

No. It is a material estimate, not a structural design, and it is not engineering advice. It reads sizes from a published prescriptive guide so the list is realistic, but it does not check your site, height, snow load, stairs, guards or the connection to the house. A permit needs a plan that your building department accepts.

Online Quote Form Setup

Let your website write the quote

You just worked out a price by hand. This puts your price list to work on your website: a customer answers a few questions, the form works out the price from your own rates, and they get an itemized quote by email while you get the request. We set it up from your price list and host it for you, so there is no monthly fee to us.

  • One quote request form for your business, with up to 10 questions and up to 15 priced items or options from your own price list
  • The price worked out from your rates the moment the customer submits, with no reply needed from you
  • An itemized quote emailed to the customer in your business name and colors, and an alert to you with every answer
  • Every request saved to a Google Sheet that you own
  • Added to your current website as an embed or a button, or delivered as its own page, with one round of changes
$395one time

Turnaround: Live within 5 business days of getting your price list and logo.

You pay on Stripe's secure checkout page. We never see your card number.