Siding Calculator

Enter the wall length and height, the gables and the openings. You get the net wall area, the squares to order with waste, and that order as vinyl cartons, lap planks or whole squares.

All walls being sided, added together. For a whole house, the perimeter.

Bottom of the siding to the eave, not counting gables.

The triangles under the roof. 0 for a hip roof.

Base to peak, at the center.

Dormer sides or any wall you measured separately.

21 is a 3 x 7 ft opening.

12 is a 3 x 4 ft opening.

A 16 x 7 ft garage door is 112 sq ft.

How to treat openings
Siding type

Printed on the carton label. The Georgia-Pacific carton we checked holds 2.

10% is the industry worksheet figure. Raise it for many gables or angles.

Printed on the saved estimate.

Siding estimate

Your siding estimate

Siding to order

8 cartons

14.55 squares with 10% waste added. An estimate, so check it against the walls before you order.

Net wall area

1,323 sq ft

Area with waste

1,455 sq ft

How the area adds up
PartAmount
Walls140 ft of wall x 9 ft high1,260 sq ft
Gables2 x (30 ft wide x 7.5 ft high / 2)225 sq ft
Openings subtractedDoors, windows and large openings in full-162 sq ft
Waste, 10%On 1,323 sq ft of siding132 sq ft
Siding to order14.55 squares at 2 squares per carton8 cartons
How we calculated this

Area. Walls are the total wall length times the wall height. Each gable is a triangle: half its width times its height, the method CertainTeed gives for gable ends.

Openings.You choose. Subtracting every opening gives the tightest order. The vinyl siding industry's estimating worksheet subtracts only half of the large openings, such as garage and sliding doors, and leaves windows and entry doors in as cushion.

Waste. 10% is added to the net area. The same worksheet says to add 10 percent to all material estimates, and CertainTeed notes that low-pitch gables waste more than steep ones.

Units. One square is 100 sq ft. Vinyl is divided by the squares in a carton, lap siding by the area one plank covers (its length times its exposure), and anything else is rounded up to a whole square.

Lap exposures.James Hardie's coverage chart for 12 ft HardiePlank pairs these widths and exposures: 5 1/4 in plank, 4 in exposure; 6 1/4 in plank, 5 in exposure; 7 1/4 in plank, 6 in exposure; 8 1/4 in plank, 7 in exposure; 9 1/4 in plank, 8 in exposure. The chart rounds to the nearest plank and leaves waste out, so its counts can be one lower than these.

What this is not. Starter strip, J-channel, corner posts, trim, soffit and fasteners are measured in linear feet and are not counted here.

Sources, all opened on November 20, 2026:

Save your result

Example: a 40 by 30 ft house with two gable ends

A house with 140 ft of wall 9 ft high and 2 gables 30 ft wide and 7.5 ft high has 1,485 sq ft of wall. Less 2 doors and 10 windows that is 1,323 sq ft, and with 10% waste 14.55 squares: 8 cartons of vinyl siding at 2 squares a carton, or 208 lap planks 12 ft long at a 7 inch exposure.

Example siding estimate

Siding to order

8 cartons

14.55 squares with 10% waste added. An estimate, so check it against the walls before you order.

Net wall area

1,323 sq ft

Area with waste

1,455 sq ft

How the area adds up
PartAmount
Walls140 ft of wall x 9 ft high1,260 sq ft
Gables2 x (30 ft wide x 7.5 ft high / 2)225 sq ft
Openings subtractedDoors, windows and large openings in full-162 sq ft
Waste, 10%On 1,323 sq ft of siding132 sq ft
Siding to order14.55 squares at 2 squares per carton8 cartons
How we calculated this

Area. Walls are the total wall length times the wall height. Each gable is a triangle: half its width times its height, the method CertainTeed gives for gable ends.

Openings.You choose. Subtracting every opening gives the tightest order. The vinyl siding industry's estimating worksheet subtracts only half of the large openings, such as garage and sliding doors, and leaves windows and entry doors in as cushion.

Waste. 10% is added to the net area. The same worksheet says to add 10 percent to all material estimates, and CertainTeed notes that low-pitch gables waste more than steep ones.

Units. One square is 100 sq ft. Vinyl is divided by the squares in a carton, lap siding by the area one plank covers (its length times its exposure), and anything else is rounded up to a whole square.

Lap exposures.James Hardie's coverage chart for 12 ft HardiePlank pairs these widths and exposures: 5 1/4 in plank, 4 in exposure; 6 1/4 in plank, 5 in exposure; 7 1/4 in plank, 6 in exposure; 8 1/4 in plank, 7 in exposure; 9 1/4 in plank, 8 in exposure. The chart rounds to the nearest plank and leaves waste out, so its counts can be one lower than these.

What this is not. Starter strip, J-channel, corner posts, trim, soffit and fasteners are measured in linear feet and are not counted here.

Sources, all opened on November 20, 2026:

How to calculate siding

Siding is ordered by the square, which is 100 sq ft of wall, so the job is to find the net wall area, add waste and divide by 100.

The formula, in plain words:

  1. Wall area = total wall length x wall height.
  2. Gable area = number of gables x (gable width x gable height / 2).
  3. Net area = walls + gables + any extra area, minus the openings you take out.
  4. Order area = net area x (1 + waste).
  5. Squares = order area / 100.

From squares, the order depends on what you are hanging. Vinyl comes by the carton, so divide by the squares in a carton and round up. Lap siding comes by the plank, so divide the order area by what one plank covers: its length times its exposure. A 12 ft plank at a 7 inch exposure covers 12 x 7 / 12 = 7 sq ft.

A worked example

Take a single-story house 40 by 30 ft with 9 ft walls, two gable ends 30 ft wide and 7.5 ft high, 2 doors and 10 windows.

  • Walls: 140 ft of wall x 9 ft = 1,260 sq ft.
  • Gables: 2 x (30 x 7.5 / 2) = 225 sq ft.
  • Openings: 2 doors at 21 sq ft and 10 windows at 12 sq ft, 162 sq ft.
  • Net area: 1,260 + 225 - 162 = 1,323 sq ft.
  • With 10% waste: 1,455 sq ft, or 14.55 squares.
  • Vinyl at 2 squares a carton: 7.3, so 8 cartons.
  • Lap planks, 12 ft at a 7 inch exposure: 207.9, so 208 planks.

The example result above is produced by the same calculation, so the numbers always agree.

Openings: three ways to count them

How you treat windows and doors changes the order more than most people expect.

  • Subtract every opening. The tightest number, and the right one when material is expensive or the walls are mostly glass.
  • The industry worksheet method. The estimating worksheet in the vinyl siding installation manual subtracts only large openings such as garage doors and sliding doors, and only half their area. Windows and entry doors stay in as cushion for the cuts around them.
  • Subtract nothing. The most cushion, and common on small jobs where one short carton costs more in lost time than it saves in material.

On the example house the three methods give 14.55, 16.34 and 16.34 squares, because it has no garage door. That is the difference between 8 cartons and 9.

Waste

The same worksheet says to add 10 percent to every material estimate, and CertainTeed gives the same figure. Gables are where waste climbs, because every course ends in an angle cut at both ends. CertainTeed notes that a low-pitch gable wastes more than a steep one. Raise the allowance for a house with several gables, dormers or diagonal runs, and lower it for long plain walls.

What the count leaves out

This is the siding itself. Starter strip, J-channel, corner posts, utility trim, soffit and fasteners are measured in linear feet from the same walk around the house, and the worksheet lists each one. Housewrap and flashing are separate too.

Pricing the job

Type your supplier's price per carton, plank or square and the result adds a material cost. No price is built in, because siding prices vary by product, color and region.

If siding is your trade, the takeoff is the quick part and winning the job is the slow part. Lever builds websites for contractors that bring in estimate requests from your service area.

Common Questions

How much siding do I need?

Multiply the total length of the walls by their height, add the area of each gable (half its width times its height), subtract the openings you want to take out, and add about 10% for waste. Divide the result by 100 to get squares, which is how siding is ordered.

How many squares of siding does a 2,000 sq ft house need?

Floor area does not give you wall area, so it depends on the shape and the height. A single-story house 50 by 40 ft has 180 ft of wall, and at 9 ft high that is 1,620 sq ft before gables and openings. With 10% waste it comes to 17.82 squares, which is 9 cartons of vinyl at 2 squares a carton. The same floor area on two stories has more wall and needs more siding.

What is a square of siding?

One square is 100 sq ft of wall coverage. It is the unit suppliers quote and installers price by, so an order of 14.5 squares covers 1,450 sq ft.

How many squares are in a box of vinyl siding?

It varies by product, so read the carton label. The Georgia-Pacific Vision Pro double 5 inch siding we checked is sold 20 pieces to the carton, 12 ft long, which the listing gives as 2 squares per carton. The calculator lets you change the figure to match your product.

Should I subtract windows and doors when measuring for siding?

Many installers leave them in. The vinyl siding industry's estimating worksheet subtracts only large areas such as garage doors and sliding doors, and only half of those. Windows and entry doors stay in, which leaves material for the cuts around them. Subtracting every opening gives a tighter order with less cushion. The calculator does it either way, or leaves every opening in.

How do I measure a gable for siding?

Measure the width of the gable at its base and the height from the base to the peak at the center. The area is half the width times the height. CertainTeed suggests adding 1 ft to the height to allow for waste, and notes that lower-pitch roofs produce more waste than steeper ones.

How many fiber cement planks are in a square?

It depends on the exposure, the part of each course that shows. James Hardie's coverage chart for 12 ft HardiePlank gives 25 planks per square at a 4 inch exposure, 20 at 5 inches, 17 at 6 inches, 14 at 7 inches and 13 at 8 inches, all before waste.

Two ways to get started

Local Business Website, Monthly

Your new website, built and looked after for you

We build your local business website, then handle the hosting, the support and every change for $249 a month. Cancel anytime and the site goes with you. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.

  • A page for each service you offer, written for your business and your service area
  • An intake form that sends every inquiry to your inbox within seconds
  • We move your domain and bring over your content and photos
  • Your Google listing updated to show the right hours and number and point to the new site
  • Hosting, support and up to 3 hours of work a month
$249a month

Turnaround: Live within five business days of your changes and your domain login.

You pay on Stripe's secure checkout page. We never see your card number.

Local Business Website, One Time

Pay once and the site is yours

We build your local business website for $1,999 and it is yours from the day it goes live, with the first year of hosting and support included. After year one, $59 a month keeps it online, keeps your form sending inquiries and covers small changes. That $59 is not charged today. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.

  • A page for each service you offer, written for your business and your service area
  • An intake form that sends every inquiry to your inbox within seconds
  • We move your domain and bring over your content and photos
  • Your Google listing updated to show the right hours and number and point to the new site
  • The first year of hosting and support included
$1,999one time

Turnaround: Live within five business days of your changes and your domain login.

You pay on Stripe's secure checkout page. We never see your card number.