Roofing Calculator
Enter the building size and roof pitch, or a roof area you already measured. You get the squares, shingle bundles, underlayment rolls, ridge cap, starter strip, drip edge and nails to order, with waste added and every coverage figure sourced.
Along the ridge.
Across the ridge.
How far the roof sticks out past the wall.
Inches of rise per 12 inches of run. 0 is flat.
3 for most shingles. Some heavy lines take 4 or 5: check the wrapper.
Linear feet one bundle covers. IKO lists 20 and 36.5 for its two lines.
For high-wind areas and very steep slopes. Off counts four.
Printed on the saved list.
Roofing material list
Your material list
Shingles to order
50 bundles
16.53 squares, with 10% waste already added. An estimate, so check it against the roof before you order.
Roof area
1,503 sq ft
Pitch multiplier
1.118
| Material | Order |
|---|---|
| Shingles16.53 squares at 3 bundles per square, incl. 10% waste | 50 bundles |
| Synthetic underlayment1,653 sq ft at 1,000 sq ft per roll, incl. 10% waste | 2 rolls |
| Hip and ridge cap42 ft of ridge and hip at 20 ft per bundle, incl. 10% waste | 3 bundles |
| Starter strip84 ft of eave at 123 ft per bundle, incl. 10% waste | 1 bundle |
| Drip edge155.6 ft of eave and rake in 10 ft pieces, incl. 10% waste | 18 pieces |
| Roofing nails320 per square (four per shingle), field shingles only | 5,290 |
How we calculated this
Roof area. The building length and width, each with the overhang added on both sides, give the area the roof covers on the ground. That is multiplied by the pitch multiplier, the square root of 1 plus (rise divided by 12) squared. For 6 in 12 it is 1.118, the same figure as IKO's area conversion table.
Waste. 10% is added to every line. Owens Corning says to add 10% to 15% to all material totals, more for a complicated roof, and IKO's estimating guide works its example with 10%.
Shingles and underlayment. One square is 100 sq ft. Squares times bundles per square, rounded up to a whole bundle. Underlayment is the same area divided by the roll coverage Owens Corning gives: 10 squares for synthetic, 4 squares for #15 felt.
Edges. Ridge cap covers ridges and hips at the coverage per bundle you entered. Starter strip runs along the eaves at 123 ft per bundle (IKO Leading Edge Plus). Drip edge covers eaves and rakes in 10 ft pieces. Rake and hip lengths are worked out from the pitch, so they are longer than they look on a plan.
Nails. 320 per square at four nails per shingle, or 480 at six, per Owens Corning. Starter, ridge cap and underlayment fasteners are not counted.
What this is not. Valleys, dormers, flashing, vents and ice barrier are not listed. A roof with several sections is best entered one section at a time, or as a measured area.
Sources, all opened on November 20, 2026:
- IKO, Estimating How Much Roofing Is Required (PDF), checked 2026-11-20
- Owens Corning, DIY roofing: how to measure and estimate a roof, checked 2026-11-20
- IKO, How Many Shingles in a Bundle, published 2023-07-19, checked 2026-11-20
- Do it Best, Amerimax F5M aluminum drip edge listing (10 ft piece), checked 2026-11-20
Example: a 40 by 30 ft house with a 6 in 12 gable roof
A 40 by 30 ft house with a 12 inch overhang and a 6 in 12 gable roof has 1,503 sq ft of roof. With 10% waste that is 16.53 squares: 50 bundles of shingles at 3 bundles per square, 2 rolls of synthetic underlayment, 3 bundles of ridge cap, 1 bundle of starter strip and 18 ten-foot pieces of drip edge.
Example material list
Shingles to order
50 bundles
16.53 squares, with 10% waste already added. An estimate, so check it against the roof before you order.
Roof area
1,503 sq ft
Pitch multiplier
1.118
| Material | Order |
|---|---|
| Shingles16.53 squares at 3 bundles per square, incl. 10% waste | 50 bundles |
| Synthetic underlayment1,653 sq ft at 1,000 sq ft per roll, incl. 10% waste | 2 rolls |
| Hip and ridge cap42 ft of ridge and hip at 20 ft per bundle, incl. 10% waste | 3 bundles |
| Starter strip84 ft of eave at 123 ft per bundle, incl. 10% waste | 1 bundle |
| Drip edge155.6 ft of eave and rake in 10 ft pieces, incl. 10% waste | 18 pieces |
| Roofing nails320 per square (four per shingle), field shingles only | 5,290 |
How we calculated this
Roof area. The building length and width, each with the overhang added on both sides, give the area the roof covers on the ground. That is multiplied by the pitch multiplier, the square root of 1 plus (rise divided by 12) squared. For 6 in 12 it is 1.118, the same figure as IKO's area conversion table.
Waste. 10% is added to every line. Owens Corning says to add 10% to 15% to all material totals, more for a complicated roof, and IKO's estimating guide works its example with 10%.
Shingles and underlayment. One square is 100 sq ft. Squares times bundles per square, rounded up to a whole bundle. Underlayment is the same area divided by the roll coverage Owens Corning gives: 10 squares for synthetic, 4 squares for #15 felt.
Edges. Ridge cap covers ridges and hips at the coverage per bundle you entered. Starter strip runs along the eaves at 123 ft per bundle (IKO Leading Edge Plus). Drip edge covers eaves and rakes in 10 ft pieces. Rake and hip lengths are worked out from the pitch, so they are longer than they look on a plan.
Nails. 320 per square at four nails per shingle, or 480 at six, per Owens Corning. Starter, ridge cap and underlayment fasteners are not counted.
What this is not. Valleys, dormers, flashing, vents and ice barrier are not listed. A roof with several sections is best entered one section at a time, or as a measured area.
Sources, all opened on November 20, 2026:
- IKO, Estimating How Much Roofing Is Required (PDF), checked 2026-11-20
- Owens Corning, DIY roofing: how to measure and estimate a roof, checked 2026-11-20
- IKO, How Many Shingles in a Bundle, published 2023-07-19, checked 2026-11-20
- Do it Best, Amerimax F5M aluminum drip edge listing (10 ft piece), checked 2026-11-20
How to calculate roofing materials
Roofing materials are ordered by the square: one square is 100 sq ft of roof, and most shingles come three bundles to the square. So the whole job is finding the real roof area, adding waste, and dividing by what each package covers.
The formula, in plain words:
- Ground area = (length + overhang on both ends) x (width + overhang on both sides).
- Roof area = ground area x pitch multiplier.
- Order area = roof area x (1 + waste).
- Squares = order area / 100, and bundles = squares x bundles per square, rounded up.
The pitch multiplier
A sloped roof is bigger than the floor under it. The multiplier is the square root of 1 plus (rise / 12) squared, and it matches the conversion table in IKO's estimating guide.
- 4 in 12: 1.054
- 6 in 12: 1.118
- 8 in 12: 1.202
- 10 in 12: 1.302
- 12 in 12: 1.414
A 12 in 12 roof needs 41% more shingles than the footprint suggests, which is the most common way a ground-level estimate comes up short.
A worked example
Take a 40 by 30 ft house with a 12 inch overhang and a 6 in 12 gable roof.
- Ground area: 42 x 32 = 1,344 sq ft.
- Roof area: 1,344 x 1.118 = 1,503 sq ft.
- With 10% waste: 1,653 sq ft, or 16.53 squares.
- Shingles: 16.53 x 3 = 49.6, so 50 bundles.
- Synthetic underlayment at 1,000 sq ft a roll: 2 rolls.
- Ridge: 42 ft plus waste is 46.2 ft, so 3 bundles of cap at 20 ft per bundle.
- Starter strip on 84 ft of eave: 1 bundle at 123 ft per bundle.
- Drip edge on 84 ft of eave and 71.6 ft of rake, plus waste: 18 ten-foot pieces.
- Nails for the field shingles at 320 per square: 5,290.
The example result above is produced by the same calculation, so the numbers always agree.
Hips, rakes and why edges run long
Edges that climb the slope are longer than they look on a plan. A rake is half the building width times the pitch multiplier. A hip is longer still: its run is multiplied by the square root of 2 plus (rise / 12) squared, which is 1.5 at 6 in 12. The calculator works these out for gable, hip and shed roofs, so ridge cap and drip edge are not guessed.
When to enter a measured area instead
The footprint method assumes one pitch and a simple shape. For a roof with wings, dormers or two pitches, measure each plane, add them up, and switch the calculator to "I measured the roof". Enter the ridge, hip, eave and rake lengths from the same takeoff and pick the 15% waste setting.
Valleys, flashing, vents and ice barrier are not on the list, so add them to your order by hand.
Pricing the job
Type your supplier's price per bundle and per roll and the result adds a material cost. No price is built in, because shingle prices move by region and by month.
If roofing is your business, the quantities are the easy part and getting the call is the hard part. See what goes on websites for roofing companies that bring in estimate requests.
Common Questions
How many bundles of shingles are in a square?
Three, for most shingles. Owens Corning says laminate shingles are generally packaged three bundles to the square, and IKO lists three for its Cambridge, Dynasty and Royal Estate lines. Heavier designer shingles take more: IKO lists four bundles per square for Crowne Slate and five for Armourshake. The count is printed on the wrapper, and the calculator lets you change it.
How do I work out roof area without getting on the roof?
Measure the building's length and width on the ground, add the overhang to each side, and multiply the two to get the area the roof covers. Then multiply by the pitch multiplier, which is the square root of 1 plus the rise over 12, squared. A 6 in 12 roof has a multiplier of 1.118, so 1,344 sq ft on the ground is about 1,503 sq ft of roof.
How much waste should I add for shingles?
Owens Corning says to add 10% to 15% to all material totals, with more for a complicated roof, and IKO gives the same 10 to 15 percent as its general range. The calculator uses 10% for a plain gable or shed roof and 15% for a roof with hips, valleys or dormers. You can type your own figure if your crew runs tighter or the roof is unusually cut up.
How many squares of shingles does a 2,000 sq ft house need?
It depends on the pitch and the overhang. A roof covering 2,000 sq ft on the ground at 6 in 12 has about 2,236 sq ft of surface, which is 22.4 squares. With 10% waste that is 24.6 squares, or 74 bundles at three bundles per square. At 9 in 12 the same footprint needs 27.5 squares with waste, or 83 bundles.
How many roofing nails do I need per square?
Owens Corning gives 320 nails per square for field shingles at four nails per shingle, and 480 per square where six nails per shingle are required, such as high-wind areas and mansards. The calculator counts field shingles only, so allow more for starter strip, ridge cap and underlayment.
How much underlayment do I need?
Enough to cover the whole roof area plus waste. Owens Corning lists synthetic underlayment in 10-square rolls and #15 felt in 4-square rolls, so a 16.5-square order is 2 rolls of synthetic or 5 rolls of #15 felt.
What is roof pitch and how do I find it?
Pitch, or slope, is how many inches the roof rises for every 12 inches it runs level. In the attic, hold a level against a rafter, mark 12 inches along it and measure straight up to the rafter: that distance is the rise. IKO also describes reading it from the ground with a pitch card or a folding rule.
Sources
- IKO, Estimating How Much Roofing Is Required (PDF): slope conversion tables and a 10% waste example, checked 2026-11-20
- Owens Corning, DIY roofing: bundles per square, 10% to 15% waste, underlayment roll sizes and nails per square, checked 2026-11-20
- IKO, How Many Shingles in a Bundle, published 2023-07-19: bundles per square by product, ridge cap and starter coverage, checked 2026-11-20
- Do it Best, Amerimax F5M aluminum drip edge listing (10 ft piece), checked 2026-11-20
Two ways to get started
Your new website, built and looked after for you
We build your local business website, then handle the hosting, the support and every change for $249 a month. Cancel anytime and the site goes with you. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.
- A page for each service you offer, written for your business and your service area
- An intake form that sends every inquiry to your inbox within seconds
- We move your domain and bring over your content and photos
- Your Google listing updated to show the right hours and number and point to the new site
- Hosting, support and up to 3 hours of work a month
Turnaround: Live within five business days of your changes and your domain login.
You pay on Stripe's secure checkout page. We never see your card number.
Pay once and the site is yours
We build your local business website for $1,999 and it is yours from the day it goes live, with the first year of hosting and support included. After year one, $59 a month keeps it online, keeps your form sending inquiries and covers small changes. That $59 is not charged today. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.
- A page for each service you offer, written for your business and your service area
- An intake form that sends every inquiry to your inbox within seconds
- We move your domain and bring over your content and photos
- Your Google listing updated to show the right hours and number and point to the new site
- The first year of hosting and support included
Turnaround: Live within five business days of your changes and your domain login.
You pay on Stripe's secure checkout page. We never see your card number.
Related Tools and Guides
- Siding calculator for the walls under the roofEnter the wall length and height, the gables and the openings. You get the net wall area, the squares to order with waste, and that order as vinyl cartons, lap planks or whole squares.
- Attic insulation calculator by climate zoneEnter the area, your climate zone and what you are insulating. You get the R-value ENERGY STAR recommends and the bags of blown-in insulation, or the batts or rolls for your stud or joist spacing, needed to reach it.
- Square Footage CalculatorPick a shape, type the measurements in feet and inches, and add as many areas as the job has. You get the total in square feet, square yards, square meters and acres, plus the cost if you enter a price per square foot.
- What a roofing company website needs on itRoofing website design built for how roofs get sold: a homeowner compares three local companies, looks at finished jobs, and asks for an estimate from the one that looks like it will still be in town next year. We build your site before you pay anything. $249 a month or $1,999 one time.
- All free business toolsCalculators and generators for pricing, quoting and running a small business.