Drywall Calculator
Enter the room's length, width and wall height, take out the doors and windows, and pick a sheet size. You get the sheets, joint compound, tape and screws to order, each worked out from a manufacturer's published coverage rate.
A closet, a soffit or another room you already measured.
Adds length times width.
Set to 0 to leave doors in, as many hangers do.
21 is a 3 x 7 ft opening.
Set to 0 to leave windows in.
12 is a 3 x 4 ft opening.
For cuts and damaged sheets. Raise it for a room with many corners.
The pail or box you buy. USG lists 3.5 gallon pails and cartons.
Printed on the saved list.
Drywall material list
Your material list
Drywall to order, 4 x 8 ft sheets
19 sheets
Covers 551 sq ft with 10% waste added. An estimate, so check it against your layout before you order.
Walls
416 sq ft
Ceiling
168 sq ft
Openings subtracted
33 sq ft
Area with waste
606 sq ft
| Material | Order |
|---|---|
| Drywall sheets, 4 x 8 ft606 sq ft with 10% waste, at 32 sq ft a sheet | 19 sheets |
| Joint compound, ready-mixed5.5 gal at 9 gal per 1,000 sq ft, in 3.5 gal containers | 2 pails |
| Joint tape213 ft at 350 ft per 1,000 sq ft, in 250 ft rolls | 1 roll |
| Drywall screws1,250 per 1,000 sq ft | 758 |
How we calculated this
Area. Walls are the room perimeter times the wall height. The ceiling is length times width. Doors and windows are subtracted at the size you entered, then your waste allowance is added.
Sheets. The area with waste divided by 32 sq ft, rounded up to a whole sheet.
Compound, tape and screws. National Gypsum's estimator lists 9 gallons of joint compound, 350 ft of joint tape and 1,250 screws per 1,000 sq ft of drywall (or 2,000 nails if you nail it). Those rates are applied to the area with waste, then rounded up to whole pails and rolls.
A second opinion. USG lists about 9.4 gallons of ready-mixed compound and about 370 ft of tape per 1,000 sq ft, a few percent higher. If you are close to the next pail or roll, round up.
What this is not. Corner bead, adhesive and primer are not listed. A Level 5 finish or a heavy texture uses more compound than these rates.
Sources, all opened on November 20, 2026:
- National Gypsum, ProForm Drywall Materials Estimator and Coverage (PDF hosted by BuildSite), checked 2026-11-20
- USG, Sheetrock Brand Dust Control Joint Compound submittal sheet J1832, 9-17 (PDF hosted by Lowe's), checked 2026-11-20
- USG, Joint Tapes product data MH1178, rev. 5-99 (PDF), checked 2026-11-20
- CertainTeed, Drywall Calculator (panel sizes and its notes on openings and waste), checked 2026-11-20
Example: a 12 by 14 ft room with 8 ft walls
A 12 by 14 ft room with 8 ft walls and a ceiling, less one door and one window, has 551 sq ft to cover. With 10% waste that takes 19 sheets of 4 x 8 ft drywall, 5.45 gallons of joint compound (2 pails of 3.5 gallons), 213 ft of joint tape and 758 screws.
Example material list
Drywall to order, 4 x 8 ft sheets
19 sheets
Covers 551 sq ft with 10% waste added. An estimate, so check it against your layout before you order.
Walls
416 sq ft
Ceiling
168 sq ft
Openings subtracted
33 sq ft
Area with waste
606 sq ft
| Material | Order |
|---|---|
| Drywall sheets, 4 x 8 ft606 sq ft with 10% waste, at 32 sq ft a sheet | 19 sheets |
| Joint compound, ready-mixed5.5 gal at 9 gal per 1,000 sq ft, in 3.5 gal containers | 2 pails |
| Joint tape213 ft at 350 ft per 1,000 sq ft, in 250 ft rolls | 1 roll |
| Drywall screws1,250 per 1,000 sq ft | 758 |
How we calculated this
Area. Walls are the room perimeter times the wall height. The ceiling is length times width. Doors and windows are subtracted at the size you entered, then your waste allowance is added.
Sheets. The area with waste divided by 32 sq ft, rounded up to a whole sheet.
Compound, tape and screws. National Gypsum's estimator lists 9 gallons of joint compound, 350 ft of joint tape and 1,250 screws per 1,000 sq ft of drywall (or 2,000 nails if you nail it). Those rates are applied to the area with waste, then rounded up to whole pails and rolls.
A second opinion. USG lists about 9.4 gallons of ready-mixed compound and about 370 ft of tape per 1,000 sq ft, a few percent higher. If you are close to the next pail or roll, round up.
What this is not. Corner bead, adhesive and primer are not listed. A Level 5 finish or a heavy texture uses more compound than these rates.
Sources, all opened on November 20, 2026:
- National Gypsum, ProForm Drywall Materials Estimator and Coverage (PDF hosted by BuildSite), checked 2026-11-20
- USG, Sheetrock Brand Dust Control Joint Compound submittal sheet J1832, 9-17 (PDF hosted by Lowe's), checked 2026-11-20
- USG, Joint Tapes product data MH1178, rev. 5-99 (PDF), checked 2026-11-20
- CertainTeed, Drywall Calculator (panel sizes and its notes on openings and waste), checked 2026-11-20
How to calculate drywall
Drywall is ordered by the sheet, so the job is to find the area to cover, add waste, and divide by the area of one sheet. Finishing materials follow from the same area, at rates the board manufacturers publish.
The formula, in plain words:
- Wall area = 2 x (length + width) x wall height.
- Ceiling area = length x width.
- Area to cover = walls + ceiling + any extra area, minus the doors and windows you choose to take out.
- Order area = area to cover x (1 + waste).
- Sheets = order area / sheet area, rounded up.
A worked example
Take a 12 by 14 ft room with 8 ft walls, a ceiling, one door and one window.
- Walls: 2 x (14 + 12) x 8 = 416 sq ft.
- Ceiling: 14 x 12 = 168 sq ft.
- Openings: one 21 sq ft door and one 12 sq ft window, 33 sq ft.
- Area to cover: 416 + 168 - 33 = 551 sq ft.
- With 10% waste: 606 sq ft.
- Sheets of 4 x 8 at 32 sq ft: 18.9, so 19 sheets.
- Joint compound at 9 gallons per 1,000 sq ft: 5.45 gallons, so 2 pails of 3.5 gallons.
- Joint tape at 350 ft per 1,000 sq ft: 213 ft, so 1 roll of 250 ft.
- Screws at 1,250 per 1,000 sq ft: 758.
The example result above is produced by the same calculation, so the numbers always agree.
Where the mud, tape and screw rates come from
Most calculators give a sheet count and stop, or list compound and screws with no source. The rates here are National Gypsum's, from its drywall materials estimator: 9 gallons of joint compound, 350 ft of joint tape and 1,250 screws for every 1,000 sq ft of board. USG publishes slightly higher figures for its own products, about 9.4 gallons of ready-mixed compound and about 370 ft of tape per 1,000 sq ft. The two agree within about 6%, so if your result lands just under a full pail or roll, buy the next one.
These rates cover a standard taped and finished job. A skim-coated Level 5 finish, a heavy texture or setting-type powder changes the compound quantity, and the bag or pail label gives the coverage for that product.
Choosing a sheet size
Every standard panel is 4 ft wide, and the lengths listed by CertainTeed are 8, 9, 10 and 12 ft. Longer sheets mean fewer butt joints to tape and finish, which is why crews hang 12 ft board on long walls and ceilings when they can get it into the room. Shorter sheets are easier to carry up stairs and to hang alone. Switch the sheet size in the calculator to see how the count changes: the example room takes 19 sheets of 4 x 8 or 13 sheets of 4 x 12.
Openings: subtract them or not
Hangers disagree on this, and both methods are reasonable. Leaving doors and windows in gives you a built-in cushion, because a sheet usually spans the opening and the cutout is scrap. Taking them out gives a tighter order for a room with large openings, such as a wide cased opening or a patio door. A sensible middle is to subtract only openings wider than a sheet and leave the small ones in.
From quantities to a price
Type your supplier's price per sheet and per pail and the result adds a material cost. No price is built in, because board prices change by region and by month.
If hanging and finishing is your trade, the next step after the takeoff is a written price. Lever builds websites for contractors that turn searches in your area into estimate requests.
Common Questions
How many sheets of drywall do I need?
Add up the wall area (room perimeter times wall height) and the ceiling area (length times width), subtract large openings, add your waste allowance, and divide by the area of one sheet. A 4 x 8 ft sheet is 32 sq ft, a 4 x 10 is 40 and a 4 x 12 is 48. Always round up to a whole sheet.
How many sheets of drywall for a 12 x 12 room?
A 12 x 12 ft room with 8 ft walls has 384 sq ft of wall and 144 sq ft of ceiling, 528 sq ft in all. That is 17 sheets of 4 x 8 with nothing spare, or 19 sheets with a 10% waste allowance. Walls only, it is 12 sheets, or 14 with 10% waste.
How much joint compound do I need per sheet of drywall?
National Gypsum's estimator lists 9 gallons of joint compound per 1,000 sq ft of drywall, which is about 0.29 gallons for each 4 x 8 ft sheet. USG lists about 9.4 gallons per 1,000 sq ft for its ready-mixed compound. At the National Gypsum rate a 3.5 gallon pail finishes about 12 sheets of 4 x 8.
How many screws per sheet of drywall?
National Gypsum's estimator lists 1,250 screws per 1,000 sq ft, which is 40 screws for a 4 x 8 ft sheet and 60 for a 4 x 12. The same table lists 2,000 nails per 1,000 sq ft if you nail instead. Your local code or a fire-rated assembly can call for closer spacing, so check before you buy.
Should I subtract doors and windows when estimating drywall?
It depends on how tight you want the order. CertainTeed's estimator says not to subtract openings such as doors, windows or outlets. The usual reasoning is that the pieces cut out of them are rarely usable. Subtracting them gives a smaller order with less margin. The calculator subtracts what you enter, so set doors and windows to 0 to follow CertainTeed's method.
How much drywall tape do I need?
National Gypsum lists 350 ft of joint tape per 1,000 sq ft of drywall, and USG lists about 370 ft. At 350 ft, one 250 ft roll covers about 714 sq ft, which is 22 sheets of 4 x 8.
How much waste should I allow for drywall?
The manufacturer estimators leave waste out and tell you to add your own. The calculator starts at 10%, which is an allowance you can change, not a measured figure. Lower it for long plain walls hung with 12 ft sheets, and raise it for a room with many corners, angles or small pieces.
Sources
- National Gypsum, ProForm Drywall Materials Estimator and Coverage (PDF hosted by BuildSite): panels, compound, tape, nails and screws by area, checked 2026-11-20
- USG, Sheetrock Brand Dust Control Joint Compound submittal sheet J1832, 9-17 (PDF hosted by Lowe's): coverage and package sizes, checked 2026-11-20
- USG, Joint Tapes product data MH1178, rev. 5-99 (PDF): tape coverage and roll lengths, checked 2026-11-20
- CertainTeed, Drywall Calculator: panel sizes and its notes on openings and waste, checked 2026-11-20
Two ways to get started
Your new website, built and looked after for you
We build your local business website, then handle the hosting, the support and every change for $249 a month. Cancel anytime and the site goes with you. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.
- A page for each service you offer, written for your business and your service area
- An intake form that sends every inquiry to your inbox within seconds
- We move your domain and bring over your content and photos
- Your Google listing updated to show the right hours and number and point to the new site
- Hosting, support and up to 3 hours of work a month
Turnaround: Live within five business days of your changes and your domain login.
You pay on Stripe's secure checkout page. We never see your card number.
Pay once and the site is yours
We build your local business website for $1,999 and it is yours from the day it goes live, with the first year of hosting and support included. After year one, $59 a month keeps it online, keeps your form sending inquiries and covers small changes. That $59 is not charged today. If the site does not bring you one new customer inquiry in its first 60 days, you get every dollar back and keep the site.
- A page for each service you offer, written for your business and your service area
- An intake form that sends every inquiry to your inbox within seconds
- We move your domain and bring over your content and photos
- Your Google listing updated to show the right hours and number and point to the new site
- The first year of hosting and support included
Turnaround: Live within five business days of your changes and your domain login.
You pay on Stripe's secure checkout page. We never see your card number.
Related Tools and Guides
- Insulation calculator for the cavities behind the boardEnter the area, your climate zone and what you are insulating. You get the R-value ENERGY STAR recommends and the bags of blown-in insulation, or the batts or rolls for your stud or joist spacing, needed to reach it.
- Flooring CalculatorEnter your rooms and pick the flooring. You get the square feet to buy with a waste allowance for that material, the number of boxes from your carton's coverage, and underlayment rolls.
- Square Footage CalculatorPick a shape, type the measurements in feet and inches, and add as many areas as the job has. You get the total in square feet, square yards, square meters and acres, plus the cost if you enter a price per square foot.
- Free estimate template for the finished priceEnter the job, the line items and how far the final cost could move, and get a clear estimate that says plainly it is an estimate. Save it as a PDF or print it, with no account and nothing uploaded.
- All free business toolsCalculators and generators for pricing, quoting and running a small business.