Tile Calculator
Enter the areas you are tiling and the tile size. You get the number of tiles and boxes to buy, with a waste allowance that follows the layout, plus bags of grout and thinset.
Decimals are fine: 10 ft 6 in is 10.5.
Leave at 0 if you do not need it.
A tub, a vanity, a door or a window you will not tile.
Sets how deep the grout goes. 3/8 in is 0.375.
Printed on the box. Enter 0 to count loose tiles.
Leave at 0 to skip cost.
Printed on the saved result.
Tile estimate
Your tile order
Tile to buy
9 boxes
65 tiles cover 120 sq ft with 10% waste. Whole boxes give you 72.
Grout, 25 lb bags
1
Thinset, 50 lb bags
3
| Material | Quantity |
|---|---|
| Area to tile12 x 10 ft | 120 sq ft |
| Tile12 x 24 in tile, 10% waste, 132 sq ft to cover | 65 tiles |
| Boxes8 per box, 72 tiles, 144 sq ft of tile | 9 boxes |
| Sanded grout6.5 lb for a 1/8 in joint, 0.375 in deep | 1 25 lb bag |
| Thinset mortar1/2 x 1/2 x 1/2 in square notch trowel | 3 50 lb bags |
How we calculated this
Area. Each length times its width, added together, minus the area you asked to leave out.
Tiles. The area plus your waste allowance, divided by the floor one tile covers. That is the tile face plus one grout joint on two sides, so a wider joint means slightly fewer tiles. The count is rounded up to whole tiles, then to whole boxes.
Waste. Picking a layout sets a starting allowance: 10% for straight or brick, 15% for diagonal and 20% for herringbone. Tile makers and estimators publish 10% for a plain layout and 15% to 20% for diagonal and patterned work. Change it for a room with many corners or for tile that chips easily.
Grout.The volume of the joints (joint area in each square foot, times the tile thickness, times your area) divided by what one bag fills. Custom Building Products' chart for its sanded grout works out to about 387 cubic inches of joint per 25 lb bag, and that is the yield used here. Unsanded, epoxy and premixed grouts cover differently, so check your bag.
Thinset. Your area divided by the square feet a 50 lb bag covers with the trowel you picked. The data sheet gives 42 to 47 sq ft for this notch. The bag count uses the lower figure so you do not run short. Back-troweling large tile uses more.
What this is not. A count for a simple rectangle. It does not lay out cuts, trim pieces, bullnose or a border, and coverage on a real job depends on the substrate and the installer.
Sources for the figures used, all opened on November 20, 2026:
- clé tile, How much extra tile to buy (September 24, 2024), checked 2026-11-20
- Inch Calculator, Tile Calculator (overage by layout), checked 2026-11-20
- Custom Building Products, Polyblend Plus Sanded Grout data sheet TDS-360, coverage chart (published February 19, 2026), checked 2026-11-20
- Custom Building Products, VersaBond Professional Tile Mortar data sheet TDS-119, coverage chart (published October 7, 2026), checked 2026-11-20
Example: a 12 x 10 ft floor in 12 x 24 in tile
A 12 x 10 ft floor is 120 sq ft. In 12 x 24 in tile laid straight with a 1/8 in joint and 10% waste, that takes 65 tiles, which is 9 boxes of 8. Add 1 bag of sanded grout (6.5 lb needed) and 3 bags of thinset with a 1/2 x 1/2 x 1/2 in square notch trowel.
Example tile order
Tile to buy
9 boxes
65 tiles cover 120 sq ft with 10% waste. Whole boxes give you 72.
Grout, 25 lb bags
1
Thinset, 50 lb bags
3
| Material | Quantity |
|---|---|
| Area to tile12 x 10 ft | 120 sq ft |
| Tile12 x 24 in tile, 10% waste, 132 sq ft to cover | 65 tiles |
| Boxes8 per box, 72 tiles, 144 sq ft of tile | 9 boxes |
| Sanded grout6.5 lb for a 1/8 in joint, 0.375 in deep | 1 25 lb bag |
| Thinset mortar1/2 x 1/2 x 1/2 in square notch trowel | 3 50 lb bags |
How we calculated this
Area. Each length times its width, added together, minus the area you asked to leave out.
Tiles. The area plus your waste allowance, divided by the floor one tile covers. That is the tile face plus one grout joint on two sides, so a wider joint means slightly fewer tiles. The count is rounded up to whole tiles, then to whole boxes.
Waste. Picking a layout sets a starting allowance: 10% for straight or brick, 15% for diagonal and 20% for herringbone. Tile makers and estimators publish 10% for a plain layout and 15% to 20% for diagonal and patterned work. Change it for a room with many corners or for tile that chips easily.
Grout.The volume of the joints (joint area in each square foot, times the tile thickness, times your area) divided by what one bag fills. Custom Building Products' chart for its sanded grout works out to about 387 cubic inches of joint per 25 lb bag, and that is the yield used here. Unsanded, epoxy and premixed grouts cover differently, so check your bag.
Thinset. Your area divided by the square feet a 50 lb bag covers with the trowel you picked. The data sheet gives 42 to 47 sq ft for this notch. The bag count uses the lower figure so you do not run short. Back-troweling large tile uses more.
What this is not. A count for a simple rectangle. It does not lay out cuts, trim pieces, bullnose or a border, and coverage on a real job depends on the substrate and the installer.
Sources for the figures used, all opened on November 20, 2026:
- clé tile, How much extra tile to buy (September 24, 2024), checked 2026-11-20
- Inch Calculator, Tile Calculator (overage by layout), checked 2026-11-20
- Custom Building Products, Polyblend Plus Sanded Grout data sheet TDS-360, coverage chart (published February 19, 2026), checked 2026-11-20
- Custom Building Products, VersaBond Professional Tile Mortar data sheet TDS-119, coverage chart (published October 7, 2026), checked 2026-11-20
How to calculate how much tile you need
Tile needed is the area in square feet, plus a waste allowance, divided by the area one tile covers. Measure each floor or wall as a rectangle, multiply length by width and add the rectangles together. Take out anything you will not tile, such as a tub, a vanity or a window.
The formula, step by step:
- Area = length x width, added up for every rectangle, minus the areas left out.
- Area to cover = area x (1 + waste percent).
- Tiles = area to cover, in square inches, divided by (tile width + joint) x (tile length + joint), rounded up.
- Boxes = tiles divided by tiles per box, rounded up.
A worked example
A bathroom floor is 12 ft by 10 ft, so the area is 120 sq ft. The tile is 12 x 24 in, laid straight with a 1/8 in joint, so the waste allowance is 10% and the area to cover is 132 sq ft. That is 19,008 square inches. One tile and its joint cover 12.125 x 24.125 in, which is 292.5 square inches. 19,008 divided by 292.5 is 64.98, so you need 65 tiles. At 8 tiles to a box that is 9 boxes, which gives you 72 tiles.
Waste by layout
A layout decides how many tiles get cut at the walls, and every cut tile leaves an offcut you may not be able to use.
- Straight or brick. Cuts fall only where a row meets a wall, and an offcut can often start the next row. Starts at 10%.
- Diagonal. Every tile along every wall is cut into a triangle. Starts at 15%.
- Herringbone. Every tile along every wall is cut at an angle and few offcuts fit anywhere else. Starts at 20%.
Raise the figure for a room with many corners, for a small room where cuts are a bigger share of the floor, and for tile from a lot that may not be available again. Leftover tile from the same lot is the only way to make an invisible repair later.
Grout and thinset
Grout fills the joints, so the amount depends on how much joint there is in each square foot and how deep it is. Small tile has far more joint than large tile: a floor of 2 x 2 in mosaic takes more than three times the grout of the same floor in 12 x 12 in tile. The calculator works out the joint volume from your tile size, joint width and tile thickness, then uses the yield behind Custom Building Products' sanded grout chart to convert it to pounds.
Thinset is spread with a notched trowel, and the notch sets how much goes down. The calculator divides your area by the manufacturer's coverage for the notch you pick and uses the low end of the range. Both figures are for cement-based products from one manufacturer. Epoxy grout, premixed grout and large-format mortars cover differently, so check the bag before you buy.
Pricing a tile job
If you price tile work for customers, the material list is only the first line of the quote. Add the backer board or membrane, trim, sealer and your labor, then apply your markup. A quote template keeps those lines in one place, and the same price list can run a quote form on your own website.
Common Questions
How many tiles do I need?
Multiply the length of the area by its width to get square feet, add a waste allowance, then divide by the area one tile covers. A 12 x 10 ft floor is 120 sq ft. With 10% waste that is 132 sq ft, and a 12 x 24 in tile with a 1/8 in joint covers just over 2 sq ft, so you need 65 tiles. The calculator does this for up to four areas at once and rounds up to whole boxes.
How much extra tile should I buy for waste?
Ten percent is the usual figure for a straight or brick layout in a simple room. Tile maker clé recommends 10% as a baseline and 15% for diagonal layouts and intricate patterns, and Inch Calculator gives 15% to 20% for patterns and diagonal work. The calculator starts at 10% for straight, 15% for diagonal and 20% for herringbone, and you can change the figure.
How many tiles are in a box?
It depends on the tile, so read the box or the product page. Large tiles come only a few to a box and small ones come dozens to a box. Type the count into the tiles per box field and the calculator rounds your order up to whole boxes and tells you how many tiles that leaves you.
How much grout do I need?
It depends on the tile size, the joint width and the tile thickness, because grout fills the joints to the depth of the tile. Custom Building Products' chart for its sanded grout gives about 348 sq ft per 25 lb bag for 12 x 12 in tile with a 1/8 in joint, and only about 96 sq ft for 2 x 2 in mosaic at the same joint. The calculator works out the joint volume for your tile and converts it to pounds and 25 lb bags.
How much thinset do I need for tile?
It depends on the trowel notch. Custom Building Products lists a 50 lb bag of its VersaBond mortar at 90 to 100 sq ft with a 1/4 in square notch, 60 to 67 sq ft with a 1/4 x 3/8 in notch and 42 to 47 sq ft with a 1/2 in notch. Divide your area by the lower figure and round up. Large tile needs the deeper notch and often back-troweling, which uses more.
Does the grout joint change how many tiles I need?
Slightly. Each tile covers its own face plus one joint along two sides, so a wider joint means a few fewer tiles. On 12 x 24 in tile the difference between a 1/16 in and a 1/4 in joint is about 2%. It matters much more for small tile and mosaics.
Can I use this for a shower wall or a backsplash?
Yes. Enter each wall as its own area, using the wall's width and the height you are tiling, and put windows, niches or doors in the area to leave out. For a tub surround that is usually three walls. Trim pieces, bullnose and edge profiles are sold by the piece or the foot and are not counted here.
Sources
- clé tile, How much extra tile to buy (September 24, 2024), checked 2026-11-20
- Inch Calculator, Tile Calculator (overage by layout), checked 2026-11-20
- Custom Building Products, Polyblend Plus Sanded Grout data sheet TDS-360, coverage chart (published February 19, 2026), checked 2026-11-20
- Custom Building Products, VersaBond Professional Tile Mortar data sheet TDS-119, coverage chart (published October 7, 2026), checked 2026-11-20
Let your website write the quote
You just worked out a price by hand. This puts your price list to work on your website: a customer answers a few questions, the form works out the price from your own rates, and they get an itemized quote by email while you get the request. We set it up from your price list and host it for you, so there is no monthly fee to us.
- One quote request form for your business, with up to 10 questions and up to 15 priced items or options from your own price list
- The price worked out from your rates the moment the customer submits, with no reply needed from you
- An itemized quote emailed to the customer in your business name and colors, and an alert to you with every answer
- Every request saved to a Google Sheet that you own
- Added to your current website as an embed or a button, or delivered as its own page, with one round of changes
Turnaround: Live within 5 business days of getting your price list and logo.
You pay on Stripe's secure checkout page. We never see your card number.
Related Tools and Guides
- Flooring calculator for hardwood, laminate, vinyl plank and carpetEnter your rooms and pick the flooring. You get the square feet to buy with a waste allowance for that material, the number of boxes from your carton's coverage, and underlayment rolls.
- Square footage calculator for rooms that are not rectanglesPick a shape, type the measurements in feet and inches, and add as many areas as the job has. You get the total in square feet, square yards, square meters and acres, plus the cost if you enter a price per square foot.
- Drywall calculator for the walls behind the tileEnter the room's length, width and wall height, take out the doors and windows, and pick a sheet size. You get the sheets, joint compound, tape and screws to order, each worked out from a manufacturer's published coverage rate.
- Markup calculator, to turn material cost into a priceEnter any two of your cost, your selling price and your markup percent, and the calculator works out the third. It also shows the margin that markup produces, because the two are not the same number.
- All free business toolsCalculators and generators for pricing, quoting and running a small business.